DN 12-1

2000 CONNECTING ROD has surface rust, clean it and away you go...

$59

Partial Bearing or Ring sets, great for a small repair

DN 12-3

1600* (*type B) 2000 .020 PISTON RING set for ONE piston (3 rings)

$15

DN 12-4

1600* (*5 Main) 2000 .010 Nissan MAIN BEARINGS more severe scratches than usual which sometimes happens as bearings jostle around in box over time if not wrapped correctly at factory. If you are REALLY on a budget or just looking to change one or two bearings this will save you some dough. Set is also missing one of the 9 pieces to set, one of the larger halves for #1 or #5 journal)

$79

DN 12-5

1600* (*5 Main) 2000 .010 Nissan MAIN BEARINGS more severe scratches than usual which sometimes happens as bearings jostle around in box over time if not wrapped correctly at factory. If you are REALLY on a budget or just looking to change one or two bearings this will save you some dough

$24

DN 12-7

15/16/20 Nissan ROD BEARINGS, 010, 3pc to do 1.5 Rods

$12

DN 12-8

15/16/20 Nissan ROD BEARINGS, 020, 5pc to do 2.5 Rods

$15

DN 12-9

1600* (*type B) 2000 .040 PISTON RING set for ONE piston (3 rings)

$14

DN 12-10

2000 PISTON OIL (3rd) RING .040 1 piece STYLE just one

$4

DN 12-11

PISTONS .020" (four)by Nissan. For the 2000 but can be used as 1600 pistons as well. New, but have sat on a shelf unwrapped forever and look it. Your engine won't care though...

$350

DN 12-12

1600 PISTONS, RINGS, CONNECTING RODS, std bearings, set of 4, all new, assembled, as removed from factory new shortblock. Separate prices total about $950!

$450

DN 13-3

200O UPPER TENSIONER New Body and Spring, but Pad is used. Pad has wear (chain tracks) on it but lots of life left.

$140

DN 17-3

63-69 GAS CAP 172-10 Original Vented Chrome Cap (see pic on NEW page) Does not have key. Have a locksmith make a key (key#9025) or take locking tab off of back of cap and use as a non locking cap.

$98

DN 21-15

68-70 1600 LOWER RAD HOSE original braided style

$83

69*-70 2000 (*from VIN SRL311-09001) LOWER RAD HOSE original braided style

$83

DN 21-18

63-67 1/2 1500/1600 LARGER W/PUMP PULLEY for high rpm use or racing where idling in hot weather is not a concern. Reduces fan drag. Original equipment on some older sedans

$39

DN 24-2

70 2000 DASH and HOOD WIRING HARNESSES INFO
Use on 70 1600 / 69 2000 / 69 1600 see: INFO

$249

DN 25-4

RHD SPEEDO CABLE inner cable only
- 1600mm for right hand drive 1600s 65-70

$19

DN 25-18

67 1/2 2000 SPEEDOMETER dent in outer rim

$229

DN 25-19

67 1/2 2000 SPEEDOMETER broken glass

$179

DU 25-21

65-67 1600 Non-working. Almost new, for parts or to be repaired. Was in service for under 200 miles before it lost it's cool. Nice rim, face and glass for your speed or tach.

$69

DN 26-14

63-69 FRONT PARKLAMP socket & holder, loose wire

$9

DN 26-10

63-70 HEADLAMP BUCKET
Empty, no gasket, lamp, wiring, or retaining ring

$49

DN 26-12

63-70 HEADLAMP BUCKET Outer shell only

$24

DN 26-15

69 FRONT TEARDROP SIDE MARKER LIGHT
New, but missing outer gasket (used ones provided). Outer separate shield over wires is old, very brittle and cracked. Suggest carefully cutting it off and wrapping wires with std auto electrical tape. Currently 2 available, price is "each".

$169

DN 37-1

1500 DRIVESHAFT U-JOINT, missing one bearing cap

$39

DN 40-12

65-67 1600 WHEEL original steel 4"width

$49

DN 40-1

1600/2000 SPINDLE (AXLE) FRONT RIGHT surface rust that

DN 46-9

MASTER CYLINDER PISTON w/seals 65-67 1600

$7

DN 48-13

68-70 IGNITION LOCK ASSY INFO

$169

DN 48-14

68-70 STEERING WHEEL found one more but is last NOS wheel see INFO

$395

DN 62-44

63-70 FRONT BUMPER w/surface flaw, typical new bumper otherwise.

$495

Pictures of the damaged fenders show the major problems only. They still may have the typical minor dings, scrapes etc that ALL of the new fenders can have. All fenders can have a varying degree of creasing vertically near the rear edge where the inside fender brace from another fender rested when Nissan had these pilled high in storage. Also common is to have the point at rear of the fender bent over. They can also be damaged to a degree where they bend down at the bottom where they wrap under the car. ALL fenders can have this. I don't know why they weren't more careful with these fragile (when off the car) parts.

DN 63-4

69 FRONT FENDER, RIGHT, w/shipping damage

$349

DN 65-1

68 HOOD

DN 65-2

70 HOOD

DN 68-XX

68-70 DASHCOVER, has very minor scratch(es), tooling mark(s) or imperfection(s). Price includes $8 nonrefundable box charge

$69

WINDSHIELD NOTE:
Windshields, whether new or new w/defect are not returnable. Open carefully in presence of driver or you may lose any ability for claims to shipper. Please see WINDSHIELD INFO!

DN 72-8

68-70 WINDSHIELD, Nissan glass. Has a very small blemish or scratch about 1 1/2" down from top, 2 3/4: from right side. It looks like a VERY faint scratch but you can't feel it with your fingernail. I can't make it appear with the camera.

$345

DN 72-9

68-70 WINDSHIELD has a rough area along the TOP edge which will be covered by the weatherstrip. It is not unusual to see a rough area of some sort, but this is above our "line" of what is barely noticeable, so we have pulled the glass out of our "normal" inventory.

$325.

RETURN TO TOP

DN 76-8

DOOR LONG W/STRIP 67 1/2-70
Normally comes as a 7 foot piece made from two 3 1/2 foot pieces glued together. This one needs the two pieces glued together.

$29

DN 76-9

DOOR LONG W/STRIP 67 1/2-70 (pair)
These go around complete door opening and are about 6-7' long. Factory w/strips so they have the typical splice. These sat in a box for 11 years. They have never been outside but are not by far as new as a typical "new" w/strip is, and are starting to show it. At least the price is right! Price is for a pair.

$40

DN 78-14

REAR FENDER, RIGHT late style

$

STAINLESS DOOR & FENDER MOULDING, ODDS & ENDS here

DN 80-9

65-67 1/2 VENT FRAME Right
Empty, no glass, handle or w/strip, chrome both sides, has small scuffed area (paint inside gray to be a 67 1/2)

$69

DN 80-27

65-67 1/2 VENT W/STRIP 4pc set #802-37 one glass surround was pulled from new frame assembly and has remains of original lubricant on it, now a dry white powder. I wiped most of it off already (rolls off by just rubbing) but some traces remain.

$79

DN 80-28

67 1/2 VENT HANDLE (RH) & HOLDER, has some scratches

$39

DN 80-29

68-70 DOOR HANDLE OUTER has some small scratches

$29

DN 80-30

68-70 DOOR INNER FUZZY HORIZ W/STRIP (PAIR)

DN 80-31

65-67 (67 1/2*) DOOR INNER FUZZY HORIZ W/STRIP (PAIR)

DN 80-32

65-67 (67 1/2*) DOOR INNER FUZZY HORIZ W/STRIP (PAIR)

DN 80-38

63-64 1500 R DOOR MOULDING, has ding. Last piece

$140

DN 84-7

63-64 1500 TRUNK TWIST HANDLE the key hole cover is missing.

DN 84-10

63-64 1500 TRUNK TWIST HANDLE complete, but no key. (#1174) Will ship with a new core & key. Have a locksmith swap them. I can usually do this in 10 seconds but this one is resisting removal and I don't want to damage it with my ham fisted antics! Or have the locksmith make a key and keep the extra core as a spare.

DN 84-8

63-70 TRUNK WEATHERSTRIP #848 -02 didn't have enough glue on one of the angled corners, needs to be reglued when installed 12/21/07

$27

DN 86-1

68-70 HEADREST COVER, pair Black,
smooth vinyl with the 4 center pleats and piping (not original but a nice way to dress up old ratty headrests!) you'll need to get a scrap of regular vinyl for the back lid cover

$39

DN 86-13

68-70 HEADREST COVER, pair, smooth vinyl with the 4 center pleats and piping.Brt Red, Dk Red (not original but a nice way to dress up old ratty headrests!) you'll need to get a scrap of regular vinyl for the back lid cover

$15

DN 96-12

MIRROR, OUTSIDE, 963-04 (described/pic on New Glass/Mirror Page) has scratches, more so then the teensy ones virtually all new Nissan mirrors have. Sometimes we have 0, sometimes we have 4-5 of these.

$27

DN96-13

MIRROR, OUTSIDE, 963-13

$69

DN 97-4

TONNEAU, 68-70,
Factory Nissan Tonneau, assembled with snaps and rear bar, already cut and trimmed for cars with Factory Rollbar (not aftermarket bar) and factory headrests. Has 3-4" tear and needs to be cleaned up or redyed from sitting through the ages.

DN 99-7

ELEC MOTOR for #999-88 rdstr model

$12

RETURN TO TOP

ODDS AND ENDS ARE NEW PARTS (DN=new) we have extremely limited quantities of, or assemblies that have something missing, or have a defect or uniqueness which will be described in the listing. As this list gets longer the NUMBER KEY may be of help.

HOW TO ORDER - - - -DELIVERY CHARGES and TIME